PU system is designed to fill cans with professional construction foam by using dimethyl ether (DME) and hydrocarbon propellants (HCP) as propellants.

POLYSYSTEM 1015Z

Application:

POLYSYSTEM 1015Z two-component PU system is designed to fill cans with professional construction foam by using dimethyl ether (DME) and hydrocarbon propellants (HCP) as propellants. Polyurethane foam (PU foam) obtained from aerosol cans is used for sealing and installing heat- and noise- insulation of joints, cracks and voids; as well as for the installation of parts when performing various construction and finishing works. PU foam is stable in size and demonstrates good adhesion to the majority of construction materials (concrete, brick, stone, wood, metal, glass).

Construction foam based on POLYSYSTEM 1015Z components is designed to perform works at the temperatures ranging from -10 to +30 °C.
System description:

POLYSYSTEM 1015Z Component A is a mixture of simple polyethers and functional additives.

Component B is polymeric diphenylmethanediisocyanate of low viscosity (PMDI/PIC: WannatePM-200, Desmodur44V20L, LupranateM20 S, VoranateM229, VoratecSD100 and their counterparts produced by other manufacturers).

Typical indicators:



Foaming parameters (process sampling is done when the mass ratio of the components A : B = 100 : 140)
Foaming conditions: stirring with a mixer for 10 s at a rotation speed of 3000 min-1. Temperature of components before foaming: (20 - 22) °C. Foaming characteristics may vary depending on the foaming conditions.


Typical properties of polymineral foam insulation based on POLYSYSTEM 1015Z PU-system
Test conditions: temperature: 20 °C, humidity: 65 %


Recommended ratio:
Recommended ratios of components may vary depending on the qualitative and quantitative composition of the hydrocarbon propellant and the production conditions used by a particular consumer.


Recommendations for processing:


Filling aerosol cans with POLYSYSTEM 1015Z PU-system is carried out on special equipment. Recommended ratios of components may vary depending on the qualitative and quantitative composition of the hydrocarbon propellant and the production conditions used by a particular consumer.

Before processing, the components are thermostated up to (18 - 22) °C.

It is essential that the cans undergo "shaking" (in a shaker) at the end of the process.
The process of can-filling is performed according to the guidelines contained in the technical documentation (issued both for the equipment and the process of producing construction foam in aerosol packaging).

Tests (or use) of the finished product are done with at least 72 hours passing from the moment when the cans were filled.


Documentation

TTNPU-009-2019 technical requirements. POLYSYSTEM 1015Z polyurethane system.

Handling and storage

POLYSYSTEM 1015Z Component A warranty period of storage is 6 months - when stored in a dry place in a hermetically sealed manufacturer's container at a temperature of (10 – 25) °C.

Component B warranty period and storage conditions - in accordance with the technical data provided by the manufacturer.

The POLYSYSTEM 1015Z PU-system technical requirements and Component B safety passport are the guidelines for the transportation, storage, handling and safety of these materials. These documents are updated periodically. Ask manufacturers and/or suppliers for updated versions of relevant documents before using the PU-system. When working with the above-mentioned materials, it is necessary to pay attention to personnel health, to compliance with safety and health regulations, as well as to environment safety.

The information contained in this document is based on our current level of technical knowledge and experience. All information and technical support are provided (orally, in writing or in any other form) without any legal warranty or assurance and are subject to change without notice. Due to the large number of factors that may affect the processing and use of our materials, it is hereby understood that the processing facilities that use our materials, technical information or technical support assume a direct obligation to release us from any liability arising thereof. It is expressly agreed that processing facilities must mandatorily conduct their own testing and assessment of our materials' suitability for specific applications, including an assessment of the applicability of our materials in terms of their compliance with applicable laws, rules and regulations relating to industrial safety, occupational health and environmental protection. Any statement or recommendation that is not contained in this document is not authorized and does not put us under any kind of obligation. No provision of this document should be construed as recommending the use of any product or information in violation of any patent for the material or its use. Appropriately protected rights, including the rights of third parties, as well as existing laws and regulations must be observed by the purchaser of our products at their own responsibility.
PRODUCT REQUEST LETTER
Please write here what products you are interested in, and we will contact you within three days.
By indicating my personal data in the above form I hereby express my consent to my personal data being processed by NPU-SYSTEMS LLC in accordance with Federal Law No. 152-FZ "On Personal Data" dd. 27.07.2006 and the Personal Data Processing Policy adopted by NPU-SYSTEMS LLC.